|
poly six issue! 12 messages
Sounds like it could be memory problems...I normally install new memory chip and battery then reload patches.. aif that dont work then you need to start taking some voltage readings..using the service
Sounds like it could be memory problems...I normally install new memory chip and battery then reload patches.. aif that dont work then you need to start taking some voltage readings..using the service
|
By
Phillip Haley
·
|
|
Korg Poly-800 and EX-800 owners - where are you? 38 messages
Hi it's Mike here, I was hoping we could get a hands up roll call of all the Poly-800 or EX-800 subscribers we have on this board. Don't be shy. A quick shout out will be much appreciated. HAWK owners
Hi it's Mike here, I was hoping we could get a hands up roll call of all the Poly-800 or EX-800 subscribers we have on this board. Don't be shy. A quick shout out will be much appreciated. HAWK owners
|
By
Michael Hawkins
·
|
|
Vintage MonoPoly for sale
Hello all As much as I love it, studio changes have me putting my vintage MonoPoly up for sale. It’s a fully restored MonoPoly, excellent working and cosmetic shape, with midi, new wood case, and it h
Hello all As much as I love it, studio changes have me putting my vintage MonoPoly up for sale. It’s a fully restored MonoPoly, excellent working and cosmetic shape, with midi, new wood case, and it h
|
By
PaperStreetAudio
·
|
|
Filter "gargling" and strange Resonance 3 messages
Hi all, I encountered a problem that I think it has to do with KLM366 board and it is about the FILTER/RESONANCE: when the CUTOFF pot is on 10 it sounds good, but during it's counterclockwise turning
Hi all, I encountered a problem that I think it has to do with KLM366 board and it is about the FILTER/RESONANCE: when the CUTOFF pot is on 10 it sounds good, but during it's counterclockwise turning
|
By
aniello iaccarino
·
|
|
Synth Wizards episode 12: Polysix 5 messages
Great new episode from Syntaur about the Polysix and a little known problem (yeah right) it has... Begin forwarded message: From: Sam Mims <sam@...> Subject: [AH] Synth Wizards episode 12: Polysix Dat
Great new episode from Syntaur about the Polysix and a little known problem (yeah right) it has... Begin forwarded message: From: Sam Mims <sam@...> Subject: [AH] Synth Wizards episode 12: Polysix Dat
|
By
Ben Stuyts
·
|
|
Mono/poly hisses 4 messages
I have a vintage Mono/poly that I just purchased. I was told it was working. I turned it on and it seems like at the very least the light display works. Seems like all I can get sound wise is touch se
I have a vintage Mono/poly that I just purchased. I was told it was working. I turned it on and it seems like at the very least the light display works. Seems like all I can get sound wise is touch se
|
By
innervoicemike@...
·
|
|
Memory loss 6 messages
I recently made the mistake of moving my Polysix, (had to have some new carpet put down) after putting my studio back together my Korg has completely lost its preset memory. I can still create a sound
I recently made the mistake of moving my Polysix, (had to have some new carpet put down) after putting my studio back together my Korg has completely lost its preset memory. I can still create a sound
|
By
Dead Sea Diver
·
|
|
KORG Polysix // A Vintage Bargain? // Walkthrough and Demo 16 messages
#polysix
Nice new video from Starsky Carr about the Polysix: https://www.youtube.com/watch?v=Z2qnujNFX5Y Ben
Nice new video from Starsky Carr about the Polysix: https://www.youtube.com/watch?v=Z2qnujNFX5Y Ben
|
By
Ben Stuyts
·
|
|
ex 800 hawk 800 need help
#ex800
#hawkmod
Hello, I installed hawk800, changed dockers ic 29 and 22, everything is well connected when I turn on the ex800, the screen stays black and nothing happens... can you help me? I checked all my connect
Hello, I installed hawk800, changed dockers ic 29 and 22, everything is well connected when I turn on the ex800, the screen stays black and nothing happens... can you help me? I checked all my connect
|
By
flubcoy@...
·
|
|
MonoPoly Pitch Gradually Ascending? 8 messages
#monopoly
Hello, Trying to find why the pitch of my Korg MonoPoly gradually ascends through the registers until inaudible. Turning it off resets to to the correct pitch briefly, only to rise again. I brought it
Hello, Trying to find why the pitch of my Korg MonoPoly gradually ascends through the registers until inaudible. Turning it off resets to to the correct pitch briefly, only to rise again. I brought it
|
By
Kaleb
·
|
|
MonoPoly Pitch Gradually Ascending -- solved 2 messages
#monopoly
Thanks for all the suggestions. The short was fairly simple -- one of the rear panel jack tabs bent to touch the panel intermittently. The "ascending" oscillator problem was down to the connectors. Ko
Thanks for all the suggestions. The short was fairly simple -- one of the rear panel jack tabs bent to touch the panel intermittently. The "ascending" oscillator problem was down to the connectors. Ko
|
By
klosmon
·
|
|
DAS BOOT with the Korg Polysix Analog Synthesizer (1981)
#polysix
Hi all, It’s awfully quiet here… hope everybody is doing well and enjoying much analog goodness. This gem by RetrouSound just arrived on my youtube subscription list: https://youtu.be/Wd2v6i0cCdA Ben
Hi all, It’s awfully quiet here… hope everybody is doing well and enjoying much analog goodness. This gem by RetrouSound just arrived on my youtube subscription list: https://youtu.be/Wd2v6i0cCdA Ben
|
By
Ben Stuyts
·
|
|
Troubleshooting a very sick Polysix... 5 messages
#polysix
Hi everyone, I'm troubleshooting a very sick Polysix and hoping someone could share some troubleshooting tips. The unit has a very clean looking KLB367A (clone board) with all chips socketed. After po
Hi everyone, I'm troubleshooting a very sick Polysix and hoping someone could share some troubleshooting tips. The unit has a very clean looking KLB367A (clone board) with all chips socketed. After po
|
By
Remodulator
·
|
|
Change capacitors in PSU or replace PSU 28 messages
#polysix
Hi all I am new to mailinglists so let me know if I am doing something wrong :) I managed to get my Polysix to work with a cloned board KLM-367 PCB from Synthronics.de. (The long store is that I bough
Hi all I am new to mailinglists so let me know if I am doing something wrong :) I managed to get my Polysix to work with a cloned board KLM-367 PCB from Synthronics.de. (The long store is that I bough
|
By
Peter Blemsted-Høyer
·
|
|
PolyMix vs. ModyPoly 5 messages
#polysix
I was just looking up PolySix auctions on eBay and found this PolyMix MIDI retrofit from russia. https://www.ebay.com/itm/Full-midi-upgrade-for-Korg-Polysix-sinthesizer-PolyMix/173596798629 Apparently
I was just looking up PolySix auctions on eBay and found this PolyMix MIDI retrofit from russia. https://www.ebay.com/itm/Full-midi-upgrade-for-Korg-Polysix-sinthesizer-PolyMix/173596798629 Apparently
|
By
Chromatest J. Pantsmaker
·
|
|
Polysix - Any info on old Miditec MK-6 MIDI kit?
#polysix
I have a Polysix here with a non-functional MIDI kit installed. It’s also messing up the key assigner enough to cause problems with the keyboard (playing wrong notes, stuck notes). I unsoldered and un
I have a Polysix here with a non-functional MIDI kit installed. It’s also messing up the key assigner enough to cause problems with the keyboard (playing wrong notes, stuck notes). I unsoldered and un
|
By
Don Backshall
·
|
|
Polysix clone board - memory not working 3 messages
#polysix
I have another clone board with another problem. Worked for years, then stopped. This is my first clone board that I built maybe 10 years ago, whenever Jed first started selling them. It is usually si
I have another clone board with another problem. Worked for years, then stopped. This is my first clone board that I built maybe 10 years ago, whenever Jed first started selling them. It is usually si
|
By
Don Backshall
·
|
|
Polysix clone board - missing ground IC 27 pin 3 ? 9 messages
#polysix
I don’t know if this is an old bug and I somehow missed it or if this is new. One of my KLM-367 clone boards was calibrated and working fine for months. A couple days ago the knobs stopped responding.
I don’t know if this is an old bug and I somehow missed it or if this is new. One of my KLM-367 clone boards was calibrated and working fine for months. A couple days ago the knobs stopped responding.
|
By
Don Backshall
·
|
|
mono/poly filter env release potentiometer 6 messages
#monopoly
Dear all , i accidentally broke the release pot of the filter env and from the net i found a note by Florian regarding the potentiometers : Monopoly has 10k-B only for Sustain. Attack is 2MB-A and Dec
Dear all , i accidentally broke the release pot of the filter env and from the net i found a note by Florian regarding the potentiometers : Monopoly has 10k-B only for Sustain. Attack is 2MB-A and Dec
|
By
lore
·
|
|
Vintage Korg Blue color codes 3 messages
#polysix
#monopoly
Hi all, I wonder if anybody has the RAL or Panetone color codes for the classic Korg blue as used on the PolySix and MonoPoly front panels? That would be great. Currently I do not have access to a ref
Hi all, I wonder if anybody has the RAL or Panetone color codes for the classic Korg blue as used on the PolySix and MonoPoly front panels? That would be great. Currently I do not have access to a ref
|
By
Matthias Herrmann
·
|